[jp] Can't sync with Clie PEG-SJ22

Jonathan Murray jmurray at whoi.edu
Wed Oct 15 15:38:01 EDT 2003


Thanks, I get hung up on the ./configure. For some reason when trying to 
build pilot-link-0.11.8  it complains about readline development not 
being installed and dies.

configure: error: Development headers for readline were not found. 
Please correct.

/usr/include/readline exists

anyone seen this? I already have

readline-devel-4.2a-4
readline-4.2a-4

installed but it isn't finding them. I tried building with

CPPFLAGS=-I/usr/include/readline rpmbuild --rebuild 
pilot-link-0.11.8-1.src.rpm

however that failed as well.

thanks

Keith Boykin wrote:
> You must have pilot-link-0.11.5 or better to use with
> Clie. See www.linux-sxs.org and my write up there on
> how to set up a Sony Clie T615C to use jpilot 0.99.3
> under SuSE 8.0. I am sure it will be the similar under
> RH 7.3.
> 
> Regards,
> 
> Keith 
> ----- Original Message -----
> From: Jonathan Murray <jmurray at whoi.edu>
> To: J-Pilot Discussion List <jpilot at jpilot.org>
> Sent: Wed, 15 Oct 2003 12:36:46 -0400
> Subject: [jp] Can't sync with Clie PEG-SJ22
> 
> 
>>jpilot-0.99-87
>>pilot-link-0.9.5-13
>>2.4.20-20.7
>>Redhat 7.3
>>
>>When I try to run pilot-xfer I get the following error with either 
>>/dev/ttyUSB0 or /dev/ttyUSB1
>>
>>pilot-xfer -p /dev/ttyUSB0 --install AddressDB.pdb
>>    Port: /dev/ttyUSB0
>>
>>    Please press the HotSync button now...
>>
>>It then hangs and times out and disconnects. My system is obviously 
>>seeing the device, anyone know what I could be missing.
>>
>>ct 15 12:26:49 trilobite kernel: usbserial.c: Handspring Visor / Treo / 
>>Palm 4.0 / Clié 4.x converter detected
>>Oct 15 12:26:52 trilobite kernel: usb_control/bulk_msg: timeout
>>Oct 15 12:26:52 trilobite kernel: visor.c: visor_startup - error -110 
>>getting connection info
>>Oct 15 12:26:52 trilobite kernel: usbserial.c: Handspring Visor / Treo / 
>>Palm 4.0 / Clié 4.x converter now attached to ttyUSB0 (or usb/tts/0 for 
>>devfs)
>>Oct 15 12:26:52 trilobite kernel: usbserial.c: Handspring Visor / Treo / 
>>Palm 4.0 / Clié 4.x converter now attached to ttyUSB1 (or usb/tts/1 for 
>>devfs)
>>Oct 15 12:26:55 trilobite /etc/hotplug/usb.agent: Setup visor for USB 
>>product 54c/66/100
>>Oct 15 12:27:49 trilobite kernel: usb.c: USB disconnect on device 
>>00:1f.4-1 address 7
>>Oct 15 12:27:49 trilobite kernel: usbserial.c: Handspring Visor / Treo / 
>>Palm 4.0 / Clié 4.x converter now disconnected from ttyUSB0
>>Oct 15 12:27:49 trilobite kernel: usbserial.c: Handspring Visor / Treo / 
>>Palm 4.0 / Clié 4.x converter now disconnected from ttyUSB1
>>
>>jpilot gives the following error again with either /dev/ttyUSB0 or 
>>/dev/ttyUSB1:
>>
>>****************************************
>>  Syncing on device /dev/ttyUSB1
>>  Press the HotSync button now
>>****************************************
>>pi_bind Illegal seek
>>Check your serial port and settings
>>exiting with status -10
>>****************************************
>>
>>Ideas appreciated,
>>
>



More information about the Jpilot mailing list